summaryrefslogtreecommitdiffstats
path: root/conf/machine/boards/zc702
Commit message (Collapse)AuthorAgeFilesLines
* zc702-zynq7: Switch over to in kernel device treeNathan Rossi2016-03-062-154/+0
| | | | | | | | | | | * Switch to the device tree that is available in the kernel source tree * Remove the in layer device tree and configuration for the in layer device tree * Setup IMAGE_BOOT_FILES with the correct target device tree from the kernel source/recipe * Setup U-Boot uEnv.txt to use the correct target device tree Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
* conf/machine/boards/*: Update flash compatible stringsNathan Rossi2015-09-161-1/+1
| | | | | | | | * Update the compatible strings in the device tree to have the dummy 'm25p80' string, the valid component string as well as adding the generic 'jedec,spi-nor' string for future use. Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
* zynq7-base.dtsi: Update bindings for PHYs attached to ethernet nodesNathan Rossi2015-04-211-6/+4
| | | | | | | | | | | | * Update the bindings to match upstream definitions for the PHY * The macb driver does not follow the phy-handle property and relies on the PHY being located as the first child node of the ethernet device * Remove the MDIO node and update all boards to nest the PHY as the first child node of the ethernet device, this change is backward compatible with the bindings for the linux-xlnx xemacps driver which follows the phy-handle definition Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* boards/*-board.dtsi: Added USB PHY nodes for USB resetNathan Rossi2015-04-171-1/+8
| | | | | | | * Added information about the GPIO/MIO reset pin so that the USB can be reset by the kernel Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* boards/*.dtsi: Fix up USB PHY reset nodesNathan Rossi2014-11-041-1/+1
| | | | | | | * Use the xlnx,phy-reset-gpio property to specify the USB PHY's reset signal Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* boards/*.dtsi: Updated Zynq device treesNathan Rossi2014-10-311-4/+0
| | | | | | * Removed use of very outdated 'gpio-mask-high' and 'gpio-mask-low' Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* zc70*-zynq7-board.dtsi: Update binding for si570Nathan Rossi2014-09-221-1/+3
| | | | | | * Update the bindings for the si570 attached to the I2C bus Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* zynq7-base.dtsi: Update bindingsNathan Rossi2014-05-261-0/+2
| | | | | | | * Update QSPI, SPI, devcfg and GPIO node bindings * Flash node properties for boards Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* zynq7-mainline-gem.dtsi: RemoveNathan Rossi2014-05-211-6/+0
| | | | | | | | * These changes have been merged into the base dtsi for zynq * Clean up and remove non-required *-yocto.dts * Update machine confs Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* machine/boards: Fix-up naming of common dtsi filesNathan Rossi2014-04-302-3/+3
| | | | | | | | | | * Common dtsi's did not match the expected naming convention, renamed them to match. * zynq-7-base.dtsi -> zynq7-base.dtsi * zynq-7-mainline-gem.dtsi -> zynq7-mainline-gem.dtsi * Updated all inclusions of renamed files Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* machine: Fix inclusion of dtsi's for *-yocto devicetreesNathan Rossi2014-04-073-2/+3
| | | | | | | | * Fix inclusion of zynq-7-mainline-gem.dtsi so that nodes properties in the board level are not overwritten * Add the *-yocto.dts to the machine configurations Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* zc702-zynq7: Added zc702-zynq7-yocto.dts for linux-yoctoNathan Rossi2014-03-131-0/+5
| | | | Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* zc702-zynq7: Cleaned up device trees and configurationNathan Rossi2014-03-124-23/+9
| | | | | | * Cleaned up device trees, refactored the dts per boot args setup Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* boards/zc702: Updated device-treeNathan Rossi2013-10-231-2/+9
| | | | | | * Added additional node properties for board specific setup Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
* conf:machine Add and modify Zynq dts files.Sipke Vriend2013-08-133-2/+23
| | | | | | | | | Add zc702 ram and mmc partition2 rootfs files. Will allow the user to select between a ramdisk dtb or a mmc card rootfs. Also update typo in comment of zc706 dts file. Signed-off-by: Sipke Vriend <sipke.vriend@xilinx.com>
* machine/zc702-zynq7: Add ZC702 support to base layerNathan Rossi2013-07-151-0/+135
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
generated by cgit v1.2.3-54-g00ecf (git 2.39.0) at 2025-08-07 16:26:25 +0000