| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
| |
* Switch to the device tree that is available in the kernel source tree
* Remove the in layer device tree and configuration for the in layer
device tree
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
|
| |
|
|
|
|
|
|
| |
* Update the compatible strings in the device tree to have the dummy
'm25p80' string, the valid component string as well as adding the
generic 'jedec,spi-nor' string for future use.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
* Update the bindings to match upstream definitions for the PHY
* The macb driver does not follow the phy-handle property and relies on
the PHY being located as the first child node of the ethernet device
* Remove the MDIO node and update all boards to nest the PHY as the
first child node of the ethernet device, this change is backward
compatible with the bindings for the linux-xlnx xemacps driver which
follows the phy-handle definition
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
|
|
|
| |
* Added information about the GPIO/MIO reset pin so that the USB can be
reset by the kernel
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
|
|
|
| |
* Use the xlnx,phy-reset-gpio property to specify the USB PHY's reset
signal
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
|
|
| |
* Removed use of very outdated 'gpio-mask-high' and 'gpio-mask-low'
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
|
|
| |
* Update the bindings for the si570 attached to the I2C bus
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
|
|
|
| |
* Update QSPI, SPI, devcfg and GPIO node bindings
* Flash node properties for boards
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
|
|
|
|
| |
* These changes have been merged into the base dtsi for zynq
* Clean up and remove non-required *-yocto.dts
* Update machine confs
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
|
|
|
|
|
|
| |
* Common dtsi's did not match the expected naming convention, renamed
them to match.
* zynq-7-base.dtsi -> zynq7-base.dtsi
* zynq-7-mainline-gem.dtsi -> zynq7-mainline-gem.dtsi
* Updated all inclusions of renamed files
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
|
|
|
|
| |
* Fix inclusion of zynq-7-mainline-gem.dtsi so that nodes properties in
the board level are not overwritten
* Add the *-yocto.dts to the machine configurations
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
| |
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
|
|
| |
* Cleaned up device trees, refactored the dts per boot args setup
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
|
|
|
|
| |
* Added additional node properties for board specific setup
* Fixed up QSPI flash properties for ZC706 flash configuration
* Fixed up incorrect setup of I2C sub nodes
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
|
| |
|
|
|
|
|
|
|
| |
Add zc702 ram and mmc partition2 rootfs files. Will allow the user to
select between a ramdisk dtb or a mmc card rootfs.
Also update typo in comment of zc706 dts file.
Signed-off-by: Sipke Vriend <sipke.vriend@xilinx.com>
|
|
|
Add zc706-zynq7 machine dts files.
Signed-off-by: Sipke Vriend <sipke.vriend@xilinx.com>
|
