| Commit message (Collapse) | Author | Age | Files | Lines | |
|---|---|---|---|---|---|
| * | zcu1275-zynqmp.conf: Rename zc1275 to zcu1275 | Mukund PVVN | 2019-12-09 | 1 | -40/+0 |
| | | | | | | | | | | zc1275 is renamed to zcu1275. All the references to zc1275 is renamed to zcu1275, this patch addresses machine conf name change and other references to zcu1275 Signed-off-by: Mukund PVVN <mukundp@xilinx.com> Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com> | ||||
| * | zynq/zynqmp confs: Adding boot.scr to IMAGE_BOOT_FILES | Jaewon Lee | 2019-12-09 | 1 | -0/+1 |
| | | | | | | | | | Adding boot.scr to IMAGE_BOOT_FILES so boot.scr is included in the wic sd card generation, if wic image generation is enabled Signed-off-by: Jaewon Lee <jaewon.lee@xilinx.com> Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com> | ||||
| * | u-boot-zynq-scr: reworking boot.scr recipe to work for zynq and zynqmp | Jaewon Lee | 2019-12-09 | 1 | -0/+1 |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Separating out sample boot.cmd file for the three supported arch (zynq, zynqmp, versal), Updating devicetree, kernel, ramdisk load addresses for zynq, and dynamically setting DEVICE_TREE_NAME to either system.dtb or kernel dtb, depending on if dtg is used or not. This u-boot-zynq-scr implementation is put in to set the default boot and boot quicker than having to wait for the distro_bootcmd to cycle to the correct boot medium. For example, zynq arch has boot_targets set to "mmc mmc0 qspi usb0 pxe dhcp xilinx" and it takes about 30 seconds to try the 'xilinx' target which will run the correct bootargs. To use the boot.scr file, zynqmp boards must have BOOT.bin, Image, system.dtb, and boot.scr in the boot partition and a rootfs extracted in the second partition. Zynq boards must have BOOT.bin, uImage, system.dtb, boot.scr, and uramdisk.image.gz in the boot partition. (uramdisk.image.gz is the ${IMAGE}.cpio.gz.u-boot in deploy directory) Adding u-boot-zynq-scr dependency to all zynq and zynqmp machine confs. Conditionally adding system.dtb to IMAGE_BOOT_FILES for zcu102 to support boot.scr in qemu flow. Signed-off-by: Jaewon Lee <jaewon.lee@xilinx.com> Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com> | ||||
| * | zc1275-zynqmp.conf: Add support for zc1275 evaluation board | Jaewon Lee | 2019-06-28 | 1 | -0/+38 |
| Add initial support for the zc1275 evaluation board which has the following main features: * XCZU29DR-FFVF1760 * Samtec BullsEye cable access to: * 16 GTY transceivers * 4 GTR transceivers * 16 ADCs * 16 DACs This patch adds machine configuration file for ZC1275 Evaluation Kit with required setting of board specific yocto variables needed for compilation of bootloader, kernel and device-tree. - linux-xlnx is the kernel provider - u-boot-xlnx is the u-boot provider which will also generate SPL boot.bin While using SPL flow, you may need to provide additional hack to pass the PMU config object. This is similar to all ZU+ boards, due to gap in SPL flow unable to load PMU config object. Signed-off-by: Jaewon Lee <jaewon.lee@xilinx.com> Signed-off-by: Manjukumar Matha <manjukumar.harthikote-matha@xilinx.com> | |||||
 |
index : linux/meta-xilinx.git | |
| Mirror of git.yoctoproject.org/meta-xilinx.git | N/A |
| summaryrefslogtreecommitdiffstats |