linux/meta-xilinx.git - Mirror of git.yoctoproject.org/meta-xilinx.git

	Commit message (Collapse)	Author	Age	Files	Lines
*	zc706-zynq7: Switch over to in kernel device tree	Nathan Rossi	2016-03-06	1	-143/+0
\| \| \| \| \| \| \| \|	* Switch to the device tree that is available in the kernel source tree * Remove the in layer device tree and configuration for the in layer device tree Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
*	conf/machine/boards/*: Update flash compatible strings	Nathan Rossi	2015-09-16	1	-1/+1
\| \| \| \| \| \| \| \|	* Update the compatible strings in the device tree to have the dummy 'm25p80' string, the valid component string as well as adding the generic 'jedec,spi-nor' string for future use. Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
*	zynq7-base.dtsi: Update bindings for PHYs attached to ethernet nodes	Nathan Rossi	2015-04-21	1	-6/+4
\| \| \| \| \| \| \| \| \| \| \| \|	* Update the bindings to match upstream definitions for the PHY * The macb driver does not follow the phy-handle property and relies on the PHY being located as the first child node of the ethernet device * Remove the MDIO node and update all boards to nest the PHY as the first child node of the ethernet device, this change is backward compatible with the bindings for the linux-xlnx xemacps driver which follows the phy-handle definition Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
*	boards/*-board.dtsi: Added USB PHY nodes for USB reset	Nathan Rossi	2015-04-17	1	-0/+7
\| \| \| \| \| \| \|	* Added information about the GPIO/MIO reset pin so that the USB can be reset by the kernel Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
*	boards/*.dtsi: Fix up USB PHY reset nodes	Nathan Rossi	2014-11-04	1	-3/+2
\| \| \| \| \| \| \|	* Use the xlnx,phy-reset-gpio property to specify the USB PHY's reset signal Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
*	boards/*.dtsi: Updated Zynq device trees	Nathan Rossi	2014-10-31	1	-4/+0
\| \| \| \| \| \|	* Removed use of very outdated 'gpio-mask-high' and 'gpio-mask-low' Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
*	zc70*-zynq7-board.dtsi: Update binding for si570	Nathan Rossi	2014-09-22	1	-1/+3
\| \| \| \| \| \|	* Update the bindings for the si570 attached to the I2C bus Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
*	zynq7-base.dtsi: Update bindings	Nathan Rossi	2014-05-26	1	-0/+2
\| \| \| \| \| \| \|	* Update QSPI, SPI, devcfg and GPIO node bindings * Flash node properties for boards Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
*	machine: Fix inclusion of dtsi's for *-yocto devicetrees	Nathan Rossi	2014-04-07	1	-1/+0
\| \| \| \| \| \| \| \|	* Fix inclusion of zynq-7-mainline-gem.dtsi so that nodes properties in the board level are not overwritten * Add the *-yocto.dts to the machine configurations Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
*	zc706-zynq7: Cleaned up device trees and configuration	Nathan Rossi	2014-03-12	1	-0/+140
	* Cleaned up device trees, refactored the dts per boot args setup Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>